When you search heating and cooling near me Hunters creek FL, you want a truck in your driveway today, not a call center reading a script. Revixa Tech runs licensed HVAC near me in Hunters creek crews out of Orange County, seven days a week, with flat-rate pricing before we touch a single panel. We diagnose the real fault, show you the failed part, and fix it the same visit whenever the parts truck allows.
Heating and cooling near me Hunters creek FL is the licensed repair, maintenance, and replacement of the equipment that keeps a Florida home comfortable year round - the condenser, air handler, evaporator coil, refrigerant circuit, thermostat, and ductwork. A proper visit starts with a full system check: manifold gauges on the refrigerant lines, a multimeter on the capacitors and contactors, and an amp draw on the blower motor. From there we trace the actual failure instead of guessing at parts.
Hunters creek homes take a beating from the climate. Summer humidity pushes condensers past 100 degrees on the pad, and winter cold snaps still drop into the 30s overnight. That swing kills weak capacitors, dries out contactors, and turns a clogged air filter into a frozen evaporator coil within a week. If your AC is not cooling or your furnace is not heating, call (844) 796-4282 and we will get a tech out the same day.
Every service call includes a full diagnostic, a flat-rate price before work begins, and a system test through a complete cycle before we leave. Parts and labor are warrantied. What is not included is quoted separately and clearly - refrigerant beyond the first pound, ductwork modifications, and full system replacement are the common add-ons.
Manifold gauges on the refrigerant circuit, multimeter on capacitors and contactors, amp draw on the blower motor, and a combustion analyzer on gas furnaces. This 30 to 45 minute check finds the actual fault instead of guessing at the most likely part.
You get the diagnostic fee and the repair price before we start. No hourly meter, no surprise line items. If the repair needs a part we do not have, we quote the part and labor together so the number is final.
If the system is low on R-410A or R-32, we leak-test with an electronic detector and nitrogen pressure before adding a single ounce. Topping off a leaking system wastes money and hides the real problem.
A clogged air filter or dirty evaporator coil causes most frozen-system calls in Florida. We check both, clean what we can on site, and tell you honestly if a coil cleaning or duct cleaning is the better next step.
Before we pack up, the system runs a complete heating or cooling cycle. We verify supply and return temperatures, confirm the thermostat holds setpoint, and show you the readings so you know the fix worked.
You get a written record of what failed, what we replaced, and what to watch for. If a follow-up maintenance visit would prevent a repeat call, it is noted so you can decide on your own schedule.
Call (844) 796-4282 or book online. We ask what the system is doing - not cooling, not heating, short cycling, water on the floor - and match the job to a tech who knows that equipment. You get a two-hour arrival window, not a vague all-day promise.
The tech pulls the service panel, checks the thermostat, and puts manifold gauges on the refrigerant circuit. A multimeter tests capacitors and contactors, and a combustion analyzer comes out on gas furnaces. This takes 30 to 45 minutes and finds the actual fault, not the symptom.
You get the diagnosis in plain language, the failed part in your hand if you want to see it, and a flat-rate price for the repair. If the system is past saving, we tell you that too, and quote replacement honestly instead of stacking repairs on a dying unit.
Most repairs run 1 to 3 hours. Capacitors, contactors, thermostats, and blower motors are same-visit jobs. Refrigerant leaks get leak-tested, brazed with copper tubing, evacuated with a vacuum pump, and charged by weight. We test the system through a full cycle before we call it done.
We check supply and return temperatures, confirm the thermostat is holding setpoint, and show you the readings. You get a written summary of what failed and what to watch for. If a filter or coil cleaning will prevent a repeat call, we say so before we leave.
Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.
Read high-side and low-side refrigerant pressures to confirm charge, diagnose restrictions, and check compressor performance against manufacturer specs.
Recover R-410A or R-32 before opening the circuit, then pull a deep vacuum to 500 microns before recharging so moisture and air do not contaminate the system.
Test capacitors, contactors, control boards, and low-voltage wiring. Most no-cool and no-heat calls trace back to an electrical component this tool identifies in minutes.
Measure gas furnace combustion on every heating call. Confirms the burn is clean and the heat exchanger is not leaking carbon monoxide into the airstream.
Cut and flare copper tubing cleanly for leak repairs and line-set work. A bad flare is one of the most common sources of slow refrigerant leaks we find.
Pull dust, debris, and construction residue out of trunk lines and registers, then verify airflow with static pressure readings before and after.
Standard service work - opening panels, tightening fittings, replacing valves, and handling PVC drain lines on condensate systems.
A Hunters Creek homeowner called at 3 p.m. on a Saturday with the house at 88 degrees. The outdoor unit was humming but the compressor was not starting, and the thermostat was calling for cooling with no response.
A failed run capacitor and a pitted contactor were replaced on site. Cold air was restored by 6 p.m., and the system held a 20-degree temperature split between supply and return. Total repair cost was under $400.
A Westchase homeowner's heat pump ran constantly but only blew cool air during a January cold front. Two prior companies had quoted a full system replacement without testing the reversing valve or defrost board.
A failed defrost control board was the actual fault. Replaced for under $500, and the heat pump returned to normal heating operation with aux heat staging correctly. The homeowner avoided a $9,000 replacement.
A Spring Branch home had a $310 summer power bill and rooms that never reached setpoint. The AC tested fine on refrigerant and electrical, but static pressure was high and accessible duct joints in the attic were leaking badly.
We sealed accessible duct leaks with mastic and tape, corrected a crushed flex run, and cleaned the evaporator coil. The next month's bill dropped to $235, and the house held setpoint for the first time in two summers.
Most calls we run in Hunters creek fall into a handful of categories. Knowing what you are dealing with helps you describe the problem on the phone, which helps us send the right tech with the right parts.
Ask a pro →We check refrigerant charge, capacitor condition, and evaporator coil cleanliness first. A weak run capacitor or a low charge explains most no-cool calls, and both are same-visit repairs with parts we carry on the truck.
We test the ignition sequence, flame sensor, and gas pressure with a combustion analyzer. Failed igniters and dirty flame sensors are the usual culprits, and both are common parts we stock so the repair finishes the same visit.
We leak-test with an electronic detector and nitrogen pressure, find the actual leak point, then repair it with copper tubing and brazing. After evacuation with a vacuum pump, we charge R-410A or R-32 by weight to the manufacturer spec.
We test the thermostat against a calibrated reading, check the low-voltage wiring, and inspect the control board. Sometimes it is a $180 thermostat swap; sometimes it is a contactor or board issue. We diagnose before quoting either.
Most repairs in Hunters creek run $180 to $650 in 2026, including the diagnostic. A capacitor or contactor swap sits at the low end; a blower motor, control board, or refrigerant leak repair pushes toward the top. Full system replacement runs $6,500 to $12,000 depending on tonnage and ductwork. You get the flat-rate price before we start work.
Revixa Tech does, and we have been doing it since 2022. We are licensed, insured, and EPA Section 608 certified, working out of Orange County and covering Hunters creek, Westchase, Spring Branch, and the surrounding 32837 area. Call (844) 796-4282 and we will match your system to a tech who knows that brand.
Same day for most calls placed before 2 p.m., and often within two to four hours for no-cool emergencies in summer. Winter furnace calls during a cold snap can run longer because everyone calls at once, so we prioritize homes with infants, elderly residents, or no backup heat. You get a real arrival window, not a four-hour maybe.
Yes. We answer emergency calls nights, weekends, and holidays for no-cool and no-heat situations. After-hours rates are quoted before we dispatch, so you know the number before a tech rolls. If it can safely wait until morning, we will tell you that too and save you the overtime charge.
furnace repairGas furnace ignition failures and cracked igniters are common in Hunters creek once winter cold snaps hit. We test the ignition sequence, flame sensor, and gas pressure, then replace failed components the same visit so you are not layering blankets while waiting on a part.Explore →
air conditioning repairAC not cooling is our most common summer call in 32837. We check refrigerant charge, capacitor condition, and coil cleanliness before recommending anything, then repair the actual fault instead of selling a replacement you do not need yet.Explore →
furnace replacementWhen a furnace is past 15 years or has a cracked heat exchanger, replacement beats another repair. We size the new unit with an ACCA load calculation, match it to your existing ductwork, and pull the Florida permit so the install is code-correct.Explore →
air duct cleaningDuct leakage and dust buildup waste 20 to 30 percent of your cooling in Florida humidity. We clean the trunk lines and registers, seal accessible leaks with mastic, and check static pressure so the blower is not fighting a restricted system.Explore →
heating repairHeat pump and furnace heating failures get diagnosed with a combustion analyzer on gas units and full electrical testing on heat pumps. We check reversing valves, defrost boards, and aux heat strips so your system actually heats when the temperature drops.Explore →
heat pump repairHeat pumps run year round in Hunters creek and wear out faster because of it. We test the reversing valve, defrost cycle, and refrigerant charge, then repair what failed instead of replacing the whole outdoor unit on a guess.Explore →
emergency HVAC repairNo cool at 10 p.m. in August or no heat during a January cold front - we run emergency calls seven days a week. After-hours pricing is quoted before dispatch, and our techs carry the parts that fail most so most emergencies end the same night.Explore →
AC repairFrom a frozen evaporator coil to a failed compressor, AC repair is the core of what we do in Hunters creek. We test the full refrigerant circuit, electrical components, and airflow before quoting, so the repair fixes the cause and not just the symptom.Explore →Licensed, insured, and EPA-certified techs with same-day availability across Orange County. Call (844) 796-4282 and we will get a truck headed your way with a flat-rate price before we start.
Book a Service Call (844) 796-4282 →Call (844) 796-4282 any time, day or night. A live dispatcher answers, takes your address and symptoms, and gives you an arrival window. For non-emergency work, we schedule same-day and next-day slots across Hunters creek and the surrounding neighborhoods, and we text you when the technician is on the way.